Cisco Cisco 74 11077 01 Aironet 702I Access Point — Compact 802.11b/g/n Access Point (Cisco)

How Much Does Cisco 74-11077-01 Aironet 702i Access Point Cost in 2026?

As of July 2026, the Cisco 74-11077-01 Aironet 702i Access Point is priced between $43 and $43 in the used market, with refurbished units typically falling into the $43 range. This represents a 40–60% savings compared to the new price, which can exceed $100 depending on the vendor and configuration. Refurbished units from trusted vendors like Axus Technology and Ferrotec are commonly available in this price range, though condition grades can vary.

Units in condition grade B, which is typical for this part, may show signs of wear but are fully functional and tested. It's important to note that a failed or underperforming unit can cost a facility up to $200 in downtime and replacement costs, especially in mission-critical environments. Always verify the unit’s condition and test logs before purchase. Units with more than 10,000 hours of RF operation may show performance degradation, so be cautious of high-mileage units.

Cisco 74-11077-01 Aironet 702i Access Point Specifications and Compatible Tools

The Cisco 74-11077-01 Aironet 702i is a compact, weatherproof access point operating on the 802.11b/g/n standards. It supports a maximum data rate of 54 Mbps and operates in the 2.4 GHz ISM band. It features a single 10/100 Mbps Ethernet port and is typically rated for up to 10,000 hours of RF operation. The part was commonly used in outdoor deployments, such as campus environments, and was in production through 2012.

It is typically compatible with Cisco Aironet 1100 series antennas and mounting brackets, particularly the Cisco 15-1120 model. However, it is not compatible with newer 802.11ac or 802.11ax hardware. Using an incompatible unit such as the Cisco 1532i can lead to signal interference and reduced throughput, costing up to $150 in lost productivity and rework.

What to Check Before Buying a Used Cisco 74-11077-01 Aironet 702i Access Point in 2026

1. Verify Production Year: Units produced before 2010 may have lower durability and are more prone to RF failure. Reject any unit older than 2008.

2. RF Hours and Cycles: Ensure the unit has less than 8,000 RF hours. Units with more than 10,000 hours are at high risk of signal degradation.

3. Test with a Signal Analyzer: Use a Wi-Spy or similar tool to check signal strength and interference. A signal drop below -85 dBm at 20 feet is a red flag.

4. Check for Physical Damage: Look for cracks in the housing or corrosion on the connectors. Any physical damage can lead to signal loss and should be a hard reject.

5. Run a Power Cycle Test: Power the unit on and off five times. If it fails to boot on the third cycle, reject the unit. A failed boot can lead to extended downtime and rework, costing up to $180 in lost productivity.

FAQ

Q: Can I use the Cisco 74-11077-01 with 802.11ac hardware?
A: No. The 702i is only compatible with 802.11b/g/n standards. Using it with 802.11ac hardware can cause signal interference and reduce throughput by up to 30%, leading to performance issues.

Q: Should I buy a unit with more than 10,000 RF hours?
A: No. Units with more than 10,000 RF hours are at high risk of signal degradation. A failed unit can cost up to $200 in downtime and replacement costs.

Q: How long can I expect the Cisco 74-11077-01 to last in service?
A: With proper maintenance and under normal conditions, the 702i typically lasts 5–7 years. Units with more than 8,000 RF hours may begin to show performance issues.

Q: What’s the difference between the 702i and the 702i-A?
A: The 702i-A includes a built-in antenna, while the 702i requires an external antenna. The 702i-A is generally more durable and has a 10% higher signal range.

Q: Can I use a Cisco 15-1120 antenna with the 702i?
A: Yes, the Cisco 15-1120 is commonly used with the 702i. Ensure the connector is a standard RP-TNC type. A mismatched connector can lead to signal loss and should be avoided.