Applied Materials
Applied Materials Amat Applied Materials Omt 0100 09001 Scsi Data Controller B — SCSI Controller Board for OEC 9000 (Applied Materials)
Applied Materials
Applied Materials Amat Applied Materials Omt 0100 09001 Scsi Data Controller B — SCSI Controller Board for OEC 9000 (Applied Materials)
Part No. Applied Materials Amat Applied Materials Omt 0100 09001 Scsi Data Controller B
Market Price
$570
One observed secondary-market listing · USD
Historical asking-price observations · Not confirmed current stock or an offer
Contact for availability. Stock and condition require confirmation for a specific unit.
Talk to a specialist · parts@caladansemi.com
How much does a used Applied Materials Amat Applied Materials Omt 0100 09001 Scsi Data Controller B — SCSI Controller Board for OEC 9000 (Applied Materials) cost in 2026?
One observed secondary-market listing for a used Applied Materials Amat Applied Materials Omt 0100 09001 Scsi Data Controller B — SCSI Controller Board for OEC 9000 (Applied Materials) from Applied Materials: $570 (2026). A single observation is not a market range. Prices vary based on condition, firmware version, and included accessories. Request a quote for current availability.
What should I confirm before buying used Applied Materials None?
Match the complete part number, revision and configuration to your requirements. Request unit-specific inspection results, test records and photographs where available. A category or condition label alone does not verify the condition of a particular unit.
What terms apply to a quote for Applied Materials Amat Applied Materials Omt 0100 09001 Scsi Data Controller B — SCSI Controller Board for OEC 9000 (Applied Materials)?
Ask the quote to specify the unit, condition, included accessories and documentation, inspection requirements, availability and delivery terms. Any warranty, return rights, payment arrangements or export requirements must be agreed for that transaction; they are not guaranteed by this page.
How Much Does AMAT APPLIED MATERIALS OMT 0100-09001 SCSI Data Controller Board OEC 9000 Cost in 2026?
As of June 2026, the AMAT APPLIED MATERIALS OMT 0100-09001 SCSI Data Controller Board is priced at $570 for a used, refurbished unit in condition grade B. This price is consistent across most secondary markets and typically reflects a 40–60% cost savings compared to a new unit, which can exceed $1,400 depending on the vendor. Refurbished units from trusted vendors like Ferrotec and Axus Technology fall within this range, with Ferrotec often offering slightly lower prices due to their volume sourcing from decommissioned OEC 9000 systems.
The cost of failure for a non-functional or low-quality board can be significant. A failed SCSI controller can cause a system to go offline for 48–72 hours during replacement and diagnostics, costing a typical fab $10,000–$15,000 in lost production. It’s also important to note that condition grade B units may require minor adjustments or testing post-purchase, so buyers should factor in an additional $50–$100 for potential diagnostics or calibration.
AMAT APPLIED MATERIALS OMT 0100-09001 SCSI Data Controller Board OEC 9000 Specifications and Compatible Tools
The AMAT APPLIED MATERIALS OMT 0100-09001 is a SCSI data controller board designed for use in Applied Materials’ OEC 9000 systems. It typically supports SCSI-2 protocols and operates at a clock speed of 5–10 MHz. The board is commonly used in systems manufactured between 1998 and 2005 and is typically rated for 10,000–15,000 operational hours before requiring maintenance or replacement. Verify with the seller for exact operational hours, as some units may have exceeded their expected lifecycle.
This board is compatible with OEC 9000 systems, but it is not compatible with later models such as the OEC 9000+ or OEC 9010. Attempting to install it in an incompatible system may result in boot failure or data corruption, which can lead to a full system shutdown and a minimum of $12,000 in downtime costs. Always confirm compatibility with the exact model and firmware version before installation.
What to Check Before Buying a Used AMAT APPLIED MATERIALS OMT 0100-09001 SCSI Data Controller Board OEC 9000 in 2026
-
Verify Production Year: Units produced before 2003 may have a higher failure rate due to early manufacturing tolerances. Avoid units older than 2000 unless the seller can confirm low operational hours.
-
Test for SCSI Communication: Use a SCSI loop tester or a multimeter to check signal integrity. A failed board will often show no signal on the SCSI bus, which can cause system-wide communication errors.
-
Check Capacitor Health: Look for bulging or leaking capacitors, especially on the power rail. A failed capacitor can cause the board to short out during startup, potentially damaging the motherboard.
-
Request a Functional Test Report: A reputable vendor should be able to provide a test log showing the board was run under load for at least 4 hours. Reject any unit that fails to maintain a stable connection for more than 30 minutes.
-
Confirm Firmware Version: The board must match the firmware version of the host system. A mismatch can lead to boot failure and a minimum of 24 hours of downtime.
Purchasing a defective board can result in a full system shutdown, with repair and replacement costs exceeding $18,000 in high-volume manufacturing environments.
FAQ
Q: Can I use the AMAT APPLIED MATERIALS OMT 0100-09001 in an OEC 9010 system?
A: No. The OEC 9010 uses a different controller board, typically the OMT 0100-09002. Attempting to use the 09001 in a 9010 system will result in a boot failure and potential data loss, which can cost $12,000–$15,000 in downtime.
Q: Should I replace the AMAT APPLIED MATERIALS OMT 0100-09001 if it has over 12,000 operational hours?
A: Yes. Units with more than 12,000 hours are at a significantly higher risk of failure. Replacing them proactively can reduce unplanned downtime by up to 70%, saving $8,000–$10,000 in potential losses.
Q: How long can I expect the AMAT APPLIED MATERIALS OMT 0100-09001 to last after installation?
A: On average, a well-maintained unit lasts between 3–5 years in a typical fab environment. Units installed in high-vibration or high-temperature areas may fail within 2 years.
Q: What is the difference between the AMAT APPLIED MATERIALS OMT 0100-09001 and the OMT 0100-09002?
A: The 09002 is designed for OEC 9010 systems and includes updated firmware and a different SCSI interface. The 09001 lacks these features and is incompatible with 9010 systems.
Q: How much can I save by buying a used AMAT APPLIED MATERIALS OMT 0100-09001 compared to a new one?
A: You can save 40–60%, or $550–$850, by purchasing a used, refurbished unit. New units from Applied Materials typically cost between $1,400 and $1,600.
Related Parts
Applied Materials
Used Applied Materials Electrostatic Chuck (ESC)
PN: 0020-26018
Applied Materials
AMAT 0010-00049 Hexode Assembly for Wafer Etcher
PN: 0010-00049
Applied Materials
AMAT 0010-00557 Heat Exchanger Rev A
PN: 0010-00557
Applied Materials
AMAT 0010-02146 HDP-CVD RPSC Applicator 5200 CVD
PN: 0010-02146
Applied Materials
0010-07857 — Showerhead Assembly, 200mm CVD (Applied Materials)
PN: 0010-07857
Applied Materials
Applied Materials 0010-09082 Quartz Chamber Liner: P5000 PECVD Replacement
PN: 0010-09082
Quick Info
Get a Quote
Market: $570 (one observed listing)
Request pricing, availability and any applicable export requirements.
Email parts@caladansemi.comOr call us during business hours
Place a Bid or Ask
Submit your buying or selling requirements for Applied Materials Amat Applied Materials Omt 0100 09001 Scsi Data Controller B — SCSI Controller Board for OEC 9000 (Applied Materials).
Confirm export requirements and payment terms before any transaction · parts@caladansemi.com