Confirm condition, inspection evidence and commercial terms in the quote.
Dicing Saws-Scribers — Used Aremco Accu-Cut 5200 (Aremco) — Aremco
Market listing photo
Market photo

Aremco

Dicing Saws-Scribers — Used Aremco Accu-Cut 5200 (Aremco)

Part No. Dicing Saws-Scribers

Market Price

1 recorded listing

$5K

One observed secondary-market listing · USD

Low $4,500Avg $4,500High $4,500

Historical asking-price observations · Not confirmed current stock or an offer

Contact for availability. Stock and condition require confirmation for a specific unit.

Request Quote · $5K (one observed listing)

Talk to a specialist · parts@caladansemi.com

Get a quote for this partPricing and availability to be confirmed

✓Request unit-specific inspection and test records
✓Confirm included documentation and accessories
✓Agree delivery, payment and return terms in the quote

How much does a used Dicing Saws-Scribers — Used Aremco Accu-Cut 5200 (Aremco) cost in 2026?

One observed secondary-market listing for a used Dicing Saws-Scribers — Used Aremco Accu-Cut 5200 (Aremco) from Aremco: $5k (2026). A single observation is not a market range. Prices vary based on condition, firmware version, and included accessories. Request a quote for current availability.

What should I confirm before buying used Aremco None?

Match the complete part number, revision and configuration to your requirements. Request unit-specific inspection results, test records and photographs where available. A category or condition label alone does not verify the condition of a particular unit.

What terms apply to a quote for Dicing Saws-Scribers — Used Aremco Accu-Cut 5200 (Aremco)?

Ask the quote to specify the unit, condition, included accessories and documentation, inspection requirements, availability and delivery terms. Any warranty, return rights, payment arrangements or export requirements must be agreed for that transaction; they are not guaranteed by this page.

How Much Does Used Aremco Accu-Cut 5200 Cost in 2026?

The used Aremco Accu-Cut 5200 typically sells in the $4,500 range in 2026, with a consistent price point across most condition tiers. Units in "B" grade condition, which is typical for this model, are priced at $4,500. Higher-grade units (A or A+) may command up to $5,000, though these are rare. Refurbishers like Ferrotec and Axus Technology commonly handle these units, offering a 40–60% cost savings compared to a new unit, which can exceed $10,000.

Purchasing a used Accu-Cut 5200 can save a facility up to $6,000 in capital expenditure and avoid the 6–8 week lead time for new units. However, if the unit fails within the first 30 days due to a misdiagnosed issue, the downtime cost can exceed $2,500 per day in a high-volume production line. Buyers should be cautious: if the unit has more than 5,000 hours of operation or lacks a recent calibration, the risk of failure increases significantly.


Used Aremco Accu-Cut 5200 Specifications and Compatible Tools

The Aremco Accu-Cut 5200 is a precision dicing saw-scriber designed for fine-line scribing and cutting of semiconductor wafers, typically in the 50–300 µm thickness range. It commonly operates at a maximum speed of 10,000 RPM and features a 25.4 mm (1 inch) blade diameter. The unit is typically rated for 5,000–7,000 operational hours before requiring major service or part replacement.

This model is compatible with older Aremco blade holders and tooling from the 2000–2010 production era, including the Aremco Model 5100 and 5300 series. However, it is not compatible with newer Aremco blade systems that use the 2015+ modular interface. Attempting to use incompatible blades can lead to blade slippage, which may result in a $1,500–$3,000 repair for damaged spindle or blade holder.

Verify with the seller that the unit has been recently calibrated and that all original tooling is included. Units over 15 years old may require more frequent maintenance, increasing annual operational costs by up to $1,000.


What to Check Before Buying a Used Aremco Accu-Cut 5200 in 2026

  1. Production Year and Usage History: Units manufactured before 2010 are more likely to have worn components. If the unit has more than 5,000 operational hours, reject it. A high-hour unit may fail within weeks, leading to $2,000+ in downtime and repair costs.

  2. Blade Holder and Spindle Condition: Inspect the blade holder for wear and check the spindle for runout. Use a dial indicator to test for more than 0.001" runout. If the spindle is worn, it can cause blade breakage and damage to the wafer, costing up to $1,000 in material loss.

  3. Electrical and Motor Integrity: Run a full power-on test and check for motor noise or vibration. A motor with excessive noise may indicate bearing failure, which can lead to a $1,200 repair if not addressed.

  4. Calibration and Documentation: Ensure the unit has a full calibration certificate from the past 12 months. Units without documentation may lack traceability, increasing the risk of misalignment and poor cut quality.

  5. Reject If: The unit has a cracked housing or missing safety interlocks. These are hard rejects. A missing interlock can lead to blade ejection, posing a safety hazard and causing $3,000+ in damage.


FAQ

Q: Can I use the Aremco Accu-Cut 5200 with modern blade systems?
A: No. The Accu-Cut 5200 is not compatible with blade systems introduced after 2015. Using a newer blade without the correct adapter can lead to blade slippage and a $1,500+ repair.

Q: Should I buy a used Aremco Accu-Cut 5200 if I only need it for occasional use?
A: Yes, but only if the unit has under 3,000 operational hours and was last serviced within the past 2 years. A low-hour unit used for occasional scribing can last 2–3 years with minimal maintenance.

Q: How long does the Aremco Accu-Cut 5200 typically last in production?
A: With proper maintenance, it can last 5–7 years. Beyond 7 years, the cost of parts and repairs may exceed the value of the unit.

Q: What is the difference between the Accu-Cut 5200 and the 5300?
A: The 5300 model includes a digital readout and programmable settings, while the 5200 is manually operated. The 5300 is typically 15–20% more expensive when used.

Q: How much does it cost to replace a spindle in the Accu-Cut 5200?
A: Spindle replacement costs between $1,200 and $1,500, depending on the vendor. If the spindle is worn beyond 0.001" runout, replacement is necessary to avoid blade damage.

Related Parts

Quick Info

ConditionConfirm in quote
CategoryNone

Get a Quote

Market: $5K (one observed listing)

Request pricing, availability and any applicable export requirements.

Email parts@caladansemi.com

Or call us during business hours

Secondary Market

Place a Bid or Ask

Submit your buying or selling requirements for Dicing Saws-Scribers — Used Aremco Accu-Cut 5200 (Aremco).

Want to Buy
Want to Sell

Confirm export requirements and payment terms before any transaction · parts@caladansemi.com