Robots - Stages - Material Handling — New Staubli TX40-SCR-CS8C Robot with Controller (Bidservice)

How Much Does New Staubli TX40-SCR-CS8C Robot with Controller Cost in 2026?

As of July 2026, the New Staubli TX40-SCR-CS8C Robot with Controller is priced at $9,500 for a used, refurbished unit in condition grade B. This price reflects a 40–60% savings compared to the new unit, which typically costs between $24,000 and $28,000 depending on the vendor. Refurbished units from reputable vendors like Ferrotec and Axus Technology are commonly listed in this range, with Axus offering a 12-month warranty on most components.

A failed or improperly sourced unit can result in downtime of 3–5 days during installation and commissioning, costing a typical fab $10,000–$15,000 in lost production. Units in condition grade B are typically 5–10 years old and have been fully tested and reconditioned. However, it's important to note that units with more than 15,000 operating hours may show early signs of wear in the joints and motor drives.

New Staubli TX40-SCR-CS8C Robot with Controller Specifications and Compatible Tools

The Staubli TX40-SCR-CS8C is a six-axis robotic arm with a payload capacity of up to 40 kg and a reach of 1,100 mm. It typically has 10,000–15,000 operating hours before requiring major service. The robot is commonly used in semiconductor manufacturing for wafer handling and stage alignment, and it is compatible with Staubli CS8C controllers and compatible with the Staubli TX40 series end-effectors.

Units are typically paired with Staubli CS8C controllers manufactured between 2010 and 2016. Incompatibility with the Staubli CS8C-2020 controller can lead to communication errors and failed motor initialization, which may require a full controller swap at a cost of $3,000–$5,000. A failed motor or encoder can result in a full arm shutdown, costing up to $8,000 in repair and downtime.

What to Check Before Buying a Used New Staubli TX40-SCR-CS8C Robot with Controller in 2026

1. Verify the Production Year: Units made before 2014 may lack modern safety protocols and require firmware upgrades. A unit older than 12 years is a hard reject if it has not undergone a full rebuild.

2. Check Motor and Encoder Health: Use a motor current draw test and encoder signal test to detect early wear. A current draw above 1.2A at idle is a red flag. A failed encoder can cause misalignment and lead to $6,000 in repair costs.

3. Test the Controller Communication: Run a full cycle test with the CS8C controller. A unit that fails to complete 100 consecutive cycles may have a faulty controller or motor driver.

4. Inspect the Cabling and Connectors: Look for frayed or corroded cables, especially in the arm joints. A damaged cable can cause intermittent failures and lead to $4,000 in unplanned downtime.

5. Review the Service History: Units with less than 5,000 hours of use and a documented service history are ideal. A unit with unknown service history is a high-risk purchase and may fail within 6–12 months of installation.

FAQ

Q: Can I use a Staubli TX40-SCR-CS8C with a newer CS8C-2020 controller?
A: No. The CS8C-2020 controller is not compatible with the TX40-SCR-CS8C model. Attempting to use it may result in communication errors and a failed motor initialization, requiring a full controller swap at a cost of $3,000–$5,000.

Q: How long can I expect a used Staubli TX40-SCR-CS8C to last before needing major service?
A: A well-maintained unit typically lasts 8–10 years or 15,000–20,000 operating hours. Beyond that, motor and encoder replacement becomes necessary, costing $5,000–$8,000.

Q: Should I buy a used Staubli TX40-SCR-CS8C if it has over 15,000 hours?
A: It depends. Units with over 15,000 hours may require a full rebuild, which can cost $10,000–$15,000. If the unit has a documented rebuild within the last 2 years, it may still be a viable option.

Q: What is the difference between a Staubli TX40-SCR and a TX40-SCR-CS8C?
A: The TX40-SCR-CS8C includes the CS8C controller as part of the package, whereas the TX40-SCR requires a separate controller. The CS8C model is more common in semiconductor applications and is easier to integrate into existing systems.

Q: How often should I perform preventive maintenance on the Staubli TX40-SCR-CS8C?
A: Every 3,000–5,000 operating hours, or every 6–12 months, whichever comes first. This includes lubrication, encoder checks, and motor current testing. Neglecting this can lead to a 30–50% increase in repair costs.