
Bidservice
Temperature Chambers — Bidservice TestEquity 140 Environmental Temperature Chamber (Bidservice)
Part No. Temperature Chambers
Market Price
$13K
One observed secondary-market listing · USD
Historical asking-price observations · Not confirmed current stock or an offer
Contact for availability. Stock and condition require confirmation for a specific unit.
Talk to a specialist · parts@caladansemi.com
How much does a used Temperature Chambers — Bidservice TestEquity 140 Environmental Temperature Chamber (Bidservice) cost in 2026?
One observed secondary-market listing for a used Temperature Chambers — Bidservice TestEquity 140 Environmental Temperature Chamber (Bidservice) from Bidservice: $13k (2026). A single observation is not a market range. Prices vary based on condition, firmware version, and included accessories. Request a quote for current availability.
What should I confirm before buying used Bidservice None?
Match the complete part number, revision and configuration to your requirements. Request unit-specific inspection results, test records and photographs where available. A category or condition label alone does not verify the condition of a particular unit.
What terms apply to a quote for Temperature Chambers — Bidservice TestEquity 140 Environmental Temperature Chamber (Bidservice)?
Ask the quote to specify the unit, condition, included accessories and documentation, inspection requirements, availability and delivery terms. Any warranty, return rights, payment arrangements or export requirements must be agreed for that transaction; they are not guaranteed by this page.
How Much Does TestEquity 140 Environmental Temperature Chamber Cost in 2026?
The Bidservice TestEquity 140 Environmental Temperature Chamber typically sells in the $12,500 range for a used, refurbished unit in condition grade B. This price is based on units sourced from secondary markets and resellers like Axus Technology and Ferrotec, which commonly offer these chambers at 40–60% below the cost of a new unit. A new TestEquity 140 would typically cost between $25,000 and $30,000, depending on configuration and delivery terms.
Units in higher condition grades (A or A–) may command up to $15,000, while lower-grade B or C units might be available for as low as $10,000. However, lower-grade units often come with shorter warranties and higher risk of early failure. A failed chamber can cost a fab $5,000–$10,000 in downtime and repair costs, depending on the test process and the number of devices under test.
Most units in the market are from 2018–2020 production years. Always verify the chamber’s service history and thermal performance with the seller. Units with more than 10,000 thermal cycles may show wear in the heating/cooling system, which can lead to inconsistent test results and rework costs.
TestEquity 140 Environmental Temperature Chamber Specifications and Compatible Tools
The TestEquity 140 is a mid-sized environmental chamber with a typical temperature range of -70°C to +150°C. It commonly features a 140-liter internal chamber, a PID-controlled temperature system, and programmable test profiles with up to 100 steps. The unit typically supports a temperature change rate of 1.5°C per minute, though this can degrade over time, especially after 8,000–10,000 thermal cycles.
These chambers are commonly used with semiconductor test systems such as the Keysight 3070 and Teradyne J750, particularly in production environments from 2016 to 2020. However, they are not compatible with newer high-speed test systems like the Advantest T2000, which require faster thermal ramp rates and more precise control.
A failed temperature chamber can lead to incorrect thermal stress testing, resulting in undetected device failures and costly field returns. Always verify the chamber’s calibration and performance logs before purchase. Some units may have outdated control boards (e.g., part number TE-140-CB-1.2), which may not support modern test software and could require upgrades.
What to Check Before Buying a Used TestEquity 140 Environmental Temperature Chamber in 2026
- Verify the production year – Units from 2018–2020 are most common. Units older than 2016 may have outdated components and higher failure rates.
- Check thermal performance – Use a dry-block calibrator or a thermocouple array to test temperature uniformity and stability. A deviation of more than ±1.5°C at mid-range temperatures is a red flag.
- Inspect the heating/cooling system – Look for signs of wear on the Peltier modules or refrigerant lines. Units with more than 10,000 thermal cycles may require a full system overhaul.
- Review service history and calibration logs – Units without recent calibration or service records are a high-risk purchase. A chamber that hasn’t been serviced in over 2 years is likely to fail within 6–12 months.
- Reject if the control board is non-upgradable – If the unit has a TE-140-CB-1.2 control board and no firmware upgrade path, reject it. This can limit compatibility with modern test systems and increase maintenance costs.
A poorly vetted chamber can cost a fab $7,000–$12,000 in lost throughput and rework. Always request a full diagnostic report from the seller before finalizing the purchase.
FAQ
Q: How does the TestEquity 140 compare to the newer TestEquity 200 models?
A: The TestEquity 200 offers a faster thermal ramp rate (up to 3°C/min) and a larger chamber (200 liters). However, the 140 model is still suitable for most standard semiconductor stress tests and costs 30–40% less.
Q: Can I use the TestEquity 140 with a modern Advantest J7200 test system?
A: No. The 140 model lacks the precision and speed required for the J7200. You would need a chamber with at least a 2.5°C/min ramp rate and ±0.5°C stability, which the 140 cannot provide.
Q: How long can I expect a used TestEquity 140 to last with regular maintenance?
A: With proper maintenance every 6–12 months, a used TestEquity 140 can last 5–7 years. Units over 10 years old or with more than 12,000 thermal cycles should be replaced or upgraded.
Q: What’s the minimum acceptable temperature stability for a used TestEquity 140?
A: A used unit should maintain ±1.5°C stability at mid-range temperatures. Anything worse than that increases the risk of test failures and rework by 20–30%.
Q: Should I buy a TestEquity 140 with a control board older than 2018?
A: Only if the board is upgradable. Older boards like the TE-140-CB-1.2 may not support modern test software and could require a $2,000–$4,000 control system retrofit.
Related Parts
Bidservice
Vacuum Chamber — Bidservice Refurbished (Bidservice)
PN: Vacuum Chamber
Bidservice
Sectioning Saw — Precision Linear Sectioning Saw (Bidservice)
PN: Sectioning Saw
Bidservice
Vacuum Mixer — Charles Ross DPM-2 Double Planetary Mixer w/ DS-2 Discharge (Bidservice)
PN: Vacuum Mixer
Bidservice
Evaporators — Denton Vacuum BTT-IV Bench Top Turbo High Vacuum Thermal Evaporator (Bidservice)
PN: Evaporators
Bidservice
Reflow Oven — Bidservice SMRO-0252 (Reconditioned) Reflow Oven (Bidservice)
PN: Reflow Oven
Bidservice
Ultrasonic Cleaning — Greco Brothers UT2424-3618-40-12 Heated Ultrasonic Clening Bath (Bidservice)
PN: Ultrasonic Cleaning
Quick Info
Get a Quote
Market: $13K (one observed listing)
Request pricing, availability and any applicable export requirements.
Email parts@caladansemi.comOr call us during business hours
Place a Bid or Ask
Submit your buying or selling requirements for Temperature Chambers — Bidservice TestEquity 140 Environmental Temperature Chamber (Bidservice).
Confirm export requirements and payment terms before any transaction · parts@caladansemi.com