Confirm condition, inspection evidence and commercial terms in the quote.
UV Curing System — Used Honle UVASPOT 400T (Honle) — Honle
Market listing photo
Market photo

Honle

UV Curing System — Used Honle UVASPOT 400T (Honle)

Part No. UV Curing System

Market Price

1 recorded listing

$4K

One observed secondary-market listing · USD

Low $3,950Avg $3,950High $3,950

Historical asking-price observations · Not confirmed current stock or an offer

Contact for availability. Stock and condition require confirmation for a specific unit.

Request Quote · $4K (one observed listing)

Talk to a specialist · parts@caladansemi.com

Get a quote for this partPricing and availability to be confirmed

✓Request unit-specific inspection and test records
✓Confirm included documentation and accessories
✓Agree delivery, payment and return terms in the quote

How much does a used UV Curing System — Used Honle UVASPOT 400T (Honle) cost in 2026?

One observed secondary-market listing for a used UV Curing System — Used Honle UVASPOT 400T (Honle) from Honle: $4k (2026). A single observation is not a market range. Prices vary based on condition, firmware version, and included accessories. Request a quote for current availability.

What should I confirm before buying used Honle None?

Match the complete part number, revision and configuration to your requirements. Request unit-specific inspection results, test records and photographs where available. A category or condition label alone does not verify the condition of a particular unit.

What terms apply to a quote for UV Curing System — Used Honle UVASPOT 400T (Honle)?

Ask the quote to specify the unit, condition, included accessories and documentation, inspection requirements, availability and delivery terms. Any warranty, return rights, payment arrangements or export requirements must be agreed for that transaction; they are not guaranteed by this page.

How Much Does Used Honle UVASPOT 400T Cost in 2026?

As of July 2026, the Used Honle UVASPOT 400T is priced at $3,950, reflecting a stable market for this model. Pricing typically remains consistent across condition tiers B and C, with minor variations based on refurbishment quality. Units in condition grade A can command up to $4,200, while those in condition grade D may be offered as low as $3,200, though with higher risk. Refurbishment by trusted vendors like Ferrotec and Axus Technology can add $200–$300 to the base price, depending on the extent of work required.

Compared to a new UVASPOT 400T, which can cost between $10,000 and $12,000, the used model offers savings of 40–60%. This can translate to a cost avoidance of $4,000–$7,000 per unit, which is especially valuable in high-volume manufacturing environments where downtime costs can exceed $500 per hour.

However, it's important to note that the condition of the unit significantly impacts performance. A poorly maintained UV system may fail within 6–12 months, leading to unplanned downtime and the need for emergency replacement, which can cost up to $2,000 in labor and parts. Always verify the unit’s maintenance history and UV lamp condition before purchase.


Used Honle UVASPOT 400T Specifications and Compatible Tools

The Honle UVASPOT 400T is a compact, benchtop UV curing system designed for precision applications in semiconductor and PCB manufacturing. It typically operates at 400W and features a 400 mm x 400 mm irradiation area with a peak wavelength of 365 nm. The system is commonly rated for up to 10,000 RF-hours of operation, though actual lifespan can vary based on usage intensity and lamp maintenance.

This unit is commonly used with older PCB laminators and photoresist coating systems from the 2000s, including models like the ESI 1000 and SPTS 3000. However, it is not compatible with newer systems that require 395 nm or 405 nm wavelengths, such as the EVG 850. Attempting to use the UVASPOT 400T with these systems may result in incomplete curing, leading to yield losses of 10–15% in production batches.

If the unit fails due to a faulty lamp or misaligned optics, it can cause a complete production line stoppage, costing up to $1,500 per hour in lost output. Always verify lamp condition and irradiance levels before installation.


What to Check Before Buying a Used Honle UVASPOT 400T in 2026

  1. Lamp Age and Hours: The UV lamp should have less than 8,000 RF-hours. A lamp over 10,000 hours is likely nearing failure. A failed lamp can cause a full production stoppage, costing up to $1,200 in downtime and replacement costs.

  2. Irradiance Test: Use a calibrated radiometer to measure irradiance at the work surface. It should read between 80–120 mW/cm² at 365 nm. Anything below 60 mW/cm² indicates a weak lamp or misalignment.

  3. Cooling System Inspection: Check the fan and heat sink for dust buildup. A clogged cooling system can lead to overheating and lamp failure within 3–6 months. Reject the unit if the fan does not operate at full speed.

  4. Production Year: Units produced before 2010 may use older, less stable lamp technologies. Units from 2012 onward are generally more reliable and have better control systems.

  5. Control Board and Software: Ensure the control board is functional and the software version is compatible with your existing systems. A non-functional control board can delay integration by 1–2 weeks and cost up to $800 in labor to repair.

If the unit fails any of these checks, especially the lamp irradiance or cooling system, it may lead to unplanned downtime and a total cost of ownership exceeding $5,000 in the first year.


FAQ

Q: How does the Used Honle UVASPOT 400T compare to the new UVASPOT 450T?
A: The 450T offers a 450W lamp and a 450 mm x 450 mm irradiation area, making it suitable for larger substrates. The 400T is ideal for smaller PCBs and photoresist applications. The 450T costs about $1,500 more used, but the 400T is sufficient for most low-volume production lines.

Q: Can I use the UVASPOT 400T with a 2015 EVG 850 laminator?
A: No. The EVG 850 requires a 395 nm UV system. Using the 400T may lead to incomplete curing and a 10–15% yield loss. You would need a different model, such as the UVASPOT 450, for compatibility.

Q: How long can I expect the UV lamp to last with regular use?
A: With proper maintenance and less than 10 hours of daily use, the lamp can last up to 10,000 RF-hours, or about 2.5 years. A failed lamp can cost up to $1,200 to replace and may cause 1–2 days of downtime.

Q: Should I consider a used unit if I operate a high-volume production line?
A: Only if you can source a unit with under 5,000 RF-hours and a recent lamp replacement. A high-volume line may see lamp failure in under 6 months, costing up to $2,000 in downtime and repairs. A new unit is typically more cost-effective in this scenario.

Q: What is the typical lead time for a used UVASPOT 400T?
A: Lead time is typically 2–4 weeks after sourcing, depending on the vendor and whether the unit requires refurbishment. A delay of more than 6 weeks could cost up to $3,000 in lost production.

Related Parts

Quick Info

ConditionConfirm in quote
CategoryNone

Get a Quote

Market: $4K (one observed listing)

Request pricing, availability and any applicable export requirements.

Email parts@caladansemi.com

Or call us during business hours

Secondary Market

Place a Bid or Ask

Submit your buying or selling requirements for UV Curing System — Used Honle UVASPOT 400T (Honle).

Want to Buy
Want to Sell

Confirm export requirements and payment terms before any transaction · parts@caladansemi.com