Hp Hp J9731 61001 Procurve 2920 Dual Port 10Gb Thernet Sfp Mod — Networking Module for Enterprise Switches (HP)

How Much Does HP J9731-61001 ProCurve 2920 Dual Port 10GB Thernet SFP+ Module Cost in 2026?

As of July 2026, the HP J9731-61001 ProCurve 2920 Dual Port 10GB Thernet SFP+ Module is priced at $186 for a used, refurbished unit in condition grade B. This price is consistent across most secondary market vendors and is typically sourced from units that were manufactured between 2015 and 2018. Refurbished units from trusted vendors like Axus Technology and Ferrotec often carry a 12-month warranty and are tested for signal integrity and power draw.

New units from HP are no longer in production, and any remaining stock is being sold at a premium, typically over $450. This means buyers can save between 40–60% by opting for a used but well-maintained module. However, if a facility experiences a failure due to a low-quality or improperly tested module, the cost of downtime can exceed $1,200 per hour in mission-critical environments. Always verify the condition and test logs before purchase—modules with more than 10,000 operational hours are more likely to fail within 6–12 months.

HP J9731-61001 ProCurve 2920 Dual Port 10GB Thernet SFP+ Module Specifications and Compatible Tools

The HP J9731-61001 is a dual-port SFP+ module designed for high-speed data transmission at 10 Gbps. It typically supports a maximum link distance of 100 meters over copper and 300 meters over multimode fiber. The module is commonly rated for a 5-year operational life under normal conditions, though real-world performance can vary based on thermal stress and power cycling. It is compatible with HP ProCurve 2920 switches, particularly models manufactured between 2014 and 2017.

Modules with part numbers such as HP J9731-61002 are not compatible due to differences in the transceiver protocol and power requirements. Using an incompatible module can lead to port lockouts or reduced throughput, which in a data center can result in $500–$1,000 in lost productivity per incident. Always confirm compatibility with the switch model and firmware version before installation.

What to Check Before Buying a Used HP J9731-61001 ProCurve 2920 Dual Port 10GB Thernet SFP+ Module in 2026

1. Production Year: Modules produced before 2015 are more likely to have degraded components. Reject any unit older than 2013 unless it has been recently overhauled.

2. Signal Integrity Test: Request a BER (Bit Error Rate) test result. A BER of 10^-10 or better is acceptable. Units with higher error rates should be rejected.

3. Power Draw Test: Use a power meter to confirm that the module draws between 1.2 and 1.8 W. Modules drawing more than 2.0 W may cause thermal issues in the switch.

4. Firmware Compatibility: Ensure the module firmware is compatible with your switch’s firmware. Mismatched versions can cause boot failures or port instability.

5. Warranty and Test Logs: Require a 12-month warranty and a full test log from the vendor. Units without documentation should be rejected.

If a buyer purchases a faulty module, it could lead to a complete port failure, requiring a $300–$500 service call and up to 4 hours of downtime.

FAQ

Q: Can I use the HP J9731-61001 with a Cisco switch?
A: No. The HP J9731-61001 is specifically designed for HP ProCurve 2920 switches. Cisco switches typically use different SFP+ modules, such as the Cisco SFP-10G-SR. Using an incompatible module can result in port lockout or hardware damage.

Q: Should I replace my HP J9731-61001 if it’s over 8 years old?
A: Yes. Modules over 8 years old typically have a failure rate of 20–30% within 6 months. If the module has more than 8,000 operational hours, replacement is strongly recommended to avoid downtime.

Q: How long can I expect a used HP J9731-61001 to last?
A: A well-maintained used module can last 3–5 years, depending on usage and environmental conditions. Modules with less than 5,000 hours of use and a BER under 10^-10 are ideal for long-term deployment.

Q: What’s the difference between the HP J9731-61001 and the J9731-61002?
A: The J9731-61002 is a quad-port module, whereas the J9731-61001 is dual-port. The J9731-61002 is not compatible with ProCurve 2920 switches due to power and protocol differences. Using it can cause port instability and require a $200–$400 service call.

Q: Is it worth buying a used HP J9731-61001 instead of a new one?
A: Yes, if sourced from a reputable vendor. Used modules can save 40–60% versus new, and downtime from a failed module is typically $1,000+ per hour. Always verify the module’s test logs and warranty.