Hp Hp Jc617 61001 10500 24P Gbe 2P 10 Gbe Xfp Se Module — High-Performance 10-Gigabit Optical Module (HP)

How Much Does HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module Cost in 2026?

As of July 2026, the HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module typically ranges from $250 to $250, depending on condition and sourcing. Refurbished units from trusted vendors like Axus Technology and Ferrotec usually fall within this price range, offering 40–60% savings compared to new units, which can exceed $600. Used modules in "B" condition are common in this bracket and are often sourced from decommissioned HP switches and routers.

Purchasing a faulty or incompatible module can result in extended downtime, with repair or replacement costs easily exceeding $1,200 due to lost productivity and expedited shipping. It’s important to note that modules with more than 10,000 hours of operational use may show signs of degradation, affecting signal integrity and increasing the risk of failure.

HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module Specifications and Compatible Tools

The HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module is a 10-Gigabit Ethernet transceiver module designed for high-speed optical communication. It typically supports SFP+ (Small Form-Factor Pluggable) interfaces and operates at wavelengths around 850 nm for short-range multimode fiber. It commonly has a maximum data rate of 10.3125 Gbps and is typically rated for a working temperature range of 0°C to 70°C.

This module is typically compatible with HP ProCurve 5412zl switches and HP 6125XLG switches manufactured between 2010 and 2014. However, it is not compatible with HP J8764A or J8765A modules due to differences in the transceiver interface and signal protocol. Failure to use a compatible module can lead to port errors, data corruption, or even hardware damage, with repair costs often exceeding $1,500.

What to Check Before Buying a Used HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module in 2026

1. Verify the production year — Modules produced before 2012 may have higher failure rates due to early manufacturing defects. Avoid units older than 10 years.

2. Check operational hours — Modules with more than 10,000 hours of use should be tested rigorously. Use a fiber optic power meter to verify signal strength and integrity.

3. Perform a link test — Use a live network test or a loopback test to ensure the module can maintain a stable 10-Gbps connection for at least 10 minutes without errors.

4. Inspect the physical condition — Look for bent pins, cracked housing, or signs of overheating. Reject any module with visible damage to the XFP connector.

5. Request a burn-in report — Modules that have passed a 24-hour burn-in test are more likely to perform reliably. Reject if the vendor cannot provide this data.

Purchasing a defective module can lead to network outages and costly repairs. A single failed module can cost up to $2,000 in downtime and replacement.

FAQ

Q: Can I use the HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module in a Cisco switch?
A: No. This module is specifically designed for HP equipment and is not compatible with Cisco switches. Attempting to use it in a Cisco switch may result in hardware errors or port failure, which can cost up to $1,800 in repairs.

Q: Should I replace my HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module if it has over 12,000 hours of use?
A: Yes. Modules with more than 12,000 hours of use are at a significantly higher risk of failure. Replacing them proactively can prevent downtime and avoid repair costs that often exceed $2,500.

Q: How long can I expect the HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module to last?
A: With proper maintenance and under normal operating conditions, you can expect a lifespan of 8–10 years. Modules used in high-temperature environments may degrade faster, reducing their effective life by up to 30%.

Q: What’s the difference between the HP JC617-61001 and the HP J8764A module?
A: The HP J8764A is a 1-Gigabit module, while the JC617-61001 is a 10-Gigabit module. They differ in form factor, data rate, and interface protocol. Using the wrong module can lead to port incompatibility and system errors.

Q: Is it worth buying a used HP JC617-61001 10500 24P GBE / 2P 10-GBE XFP SE Module?
A: Yes, if you can verify its condition and test it before installation. Used modules can save 40–60% compared to new ones. However, avoid modules with more than 10,000 hours of use or visible damage to avoid costly failures.