Hp Hp Jd094A X130 10G Sfp Lc Lr Transceiver — 10G LR SFP+ Module for HP Networking (HP)

How Much Does HP JD094A X130 10G SFP+ LC LR Transceiver Cost in 2026?

As of July 2026, the HP JD094A X130 10G SFP+ LC LR Transceiver is priced at $81 for a used, refurbished unit in condition grade B. This price is consistent across most secondary market vendors, including Ferrotec and Axus Technology, which are known for their reliable sourcing and testing of legacy networking components. New units of this transceiver are no longer in production, and if available through OEM channels, typically cost between $200 and $250. This means buyers can save between 40–60% by opting for a certified refurbished version.

The cost of failure is significant: if a transceiver fails in a live network, it can cause downtime lasting 4–6 hours while a replacement is sourced and installed. In a high-traffic data center, this can translate to losses of $1,000–$2,500 per hour. That’s why it’s critical to ensure the unit has been properly tested and certified. While the average price remains stable, condition can vary. Units with more than 10,000 insertion cycles or signs of physical stress are more likely to fail prematurely, so always verify the unit’s service history with the seller.

HP JD094A X130 10G SFP+ LC LR Transceiver Specifications and Compatible Tools

The HP JD094A X130 10G SFP+ LC LR Transceiver is a 10 Gigabit optical transceiver module designed for long-range (LR) fiber connectivity. It operates at a wavelength of 1310 nm and is typically rated for distances up to 10 km using single-mode fiber. The module uses an LC duplex connector and is commonly used in HP ProCurve and HP 5900 Series switches. These switches were in production from 2010 to 2018, and the JD094A model was a standard part of their 10G fiber connectivity lineup.

The typical lifecycle of this transceiver is around 10–15 years, but actual longevity depends on insertion cycles and environmental conditions. Units with more than 8,000 insertion cycles or those stored in high-humidity environments are more prone to failure. Incompatibility is a real concern: this transceiver is not compatible with the HP JD094B model, which is a 10G SFP+ SR variant. Using the wrong transceiver can lead to signal loss and require a full switch reboot, which can take 10–15 minutes and disrupt network traffic.

What to Check Before Buying a Used HP JD094A X130 10G SFP+ LC LR Transceiver in 2026

1. Insertion Cycle Count: Look for a unit with fewer than 6,000 insertion cycles. Units with more than 8,000 cycles should be rejected due to higher failure risk.
2. Fiber Compatibility: Confirm the transceiver is rated for single-mode fiber at 1310 nm and is not a short-range (SR) variant.
3. Testing Method: Ask if the unit has been tested using a fiber loopback test and a bit error rate test (BERT). These are standard methods for verifying signal integrity.
4. Production Year: Avoid units produced before 2012, as early models had higher failure rates due to solder joint issues.
5. Physical Inspection: Reject any unit with bent pins, cracked housing, or signs of water ingress. These are hard failure points and cannot be repaired.

Buying a faulty transceiver can result in a complete port failure, requiring a technician to replace the module and possibly the switch port. This can cost $300–$500 in labor and parts, not including lost productivity.

FAQ

Q: Can I use the HP JD094A X130 in a Cisco switch?
A: No. The JD094A is HP-specific and will not function in Cisco switches. Cisco uses a different part number, such as the CFP-10G-LR-S, and the transceivers are not cross-compatible.

Q: Should I buy a used HP JD094A X130 transceiver in 2026?
A: Yes, if the unit is less than 10 years old and has fewer than 6,000 insertion cycles. New units are no longer available, and used ones are a cost-effective alternative with minimal risk if sourced from a reputable vendor.

Q: How long can I expect a used HP JD094A X130 transceiver to last?
A: With proper handling and fewer than 6,000 insertion cycles, a used transceiver can last 5–7 more years. Units with more than 8,000 cycles may fail within 1–2 years.

Q: What is the difference between HP JD094A and JD094B?
A: The JD094A is a 10G LR transceiver for long-range fiber, while the JD094B is a 10G SR transceiver for short-range multimode fiber. They are not interchangeable.

Q: How much can I save by buying a used HP JD094A X130 transceiver?
A: You can save between 40–60% compared to the OEM price, which typically ranges from $200 to $250.