Hp Hpe Proliant Dl380 Gen10 8 Sff 8 Sff Nvme Server Chassis — High-Density Storage Solution (HP)

How Much Does HPE ProLiant DL380 Gen10 8 SFF + 8 SFF NVMe Server Chassis Cost in 2026?

As of July 2026, the HPE ProLiant DL380 Gen10 8 SFF + 8 SFF NVMe Server Chassis is priced at $531 for a used unit in condition grade B. This price is consistent across most major refurbishment vendors such as Axus Technology and Ferrotec. A new unit from HP typically ranges between $1,300 and $1,500, meaning buyers can save between 40% and 60% by opting for a used chassis.

The price is stable for this part, with no significant fluctuations in the last 12 months. However, it's important to note that units with higher condition grades (A or A-) may cost up to $100 more, while those with a grade C or lower are typically not recommended due to increased risk of failure. A failed chassis can lead to extended downtime, with an average cost of $1,200 per hour in data centers. Always verify the condition with the seller before purchase, especially the presence of physical damage or signs of overheating.

HPE ProLiant DL380 Gen10 8 SFF + 8 SFF NVMe Server Chassis Specifications and Compatible Tools

The HPE ProLiant DL380 Gen10 8 SFF + 8 SFF NVMe Server Chassis is a 2U rackmount chassis designed to support up to 16 SFF drives—8 SAS/SATA and 8 NVMe. It supports a maximum of 2 TB of DDR4 memory and is compatible with Intel Xeon Scalable processors. The chassis is typically rated for a minimum of 50,000 RF (read/write) hours and is commonly used in environments where high-speed storage and scalability are required.

This chassis is typically compatible with HPE Smart Storage tools from 2018 to 2021, including models like the HPE Smart Array P408i. However, it is not compatible with newer HPE Gen11 storage controllers such as the HPE Smart Array P440ar. Using an incompatible controller can lead to boot failures or data loss, with recovery costs often exceeding $3,000.

What to Check Before Buying a Used HPE ProLiant DL380 Gen10 8 SFF + 8 SFF NVMe Server Chassis in 2026

1. Physical Inspection: Look for signs of overheating, such as discolored metal or warped panels. A chassis with a production year older than 2019 may have higher failure rates.

2. Drive Bays and Backplanes: Ensure all 16 SFF bays are functional and the backplane shows no signs of corrosion. A faulty backplane can lead to data access issues, costing up to $2,500 in lost productivity.

3. Power Supply Test: Use a multimeter to test the 1+1 redundant power supplies. If either supply fails to deliver 12V or more, reject the unit. A failed power supply can lead to a complete system shutdown.

4. Firmware and BIOS Check: Confirm the BIOS is updated to at least version 2.30 and that the firmware for the storage controller is compatible with Gen10 hardware. Older firmware can cause compatibility issues with newer drives.

5. Thermal Performance: Run a thermal stress test using HPE iLO. If the chassis exceeds 55°C under load, it may not be suitable for high-density environments. Overheating can lead to premature component failure and downtime.

FAQ

Q: Can I use the HPE ProLiant DL380 Gen10 chassis with Gen11 processors?
A: No. The Gen10 chassis is not compatible with Gen11 Xeon Scalable processors. Attempting to install a Gen11 CPU will result in a boot failure. You must use a Gen10 or earlier processor.

Q: Should I buy a used HPE ProLiant DL380 Gen10 chassis if it's over five years old?
A: It depends. Units older than five years may still function, but they are more likely to fail. A chassis over six years old should be inspected thoroughly, as failure rates increase significantly after 2019.

Q: How long can I expect the HPE ProLiant DL380 Gen10 chassis to last with regular maintenance?
A: With proper maintenance and a clean environment, the chassis can last up to 7–8 years. However, if the cooling system is neglected, failure can occur within 4–5 years, leading to expensive repairs.

Q: What’s the difference between the 8 SFF + 8 SFF NVMe and the standard 8 SFF + 8 SAS/SATA version?
A: The NVMe version supports up to 8 NVMe SSDs for faster data access, while the standard version only supports SAS/SATA drives. The NVMe variant is ideal for high-performance computing and low-latency applications.

Q: Is the HPE ProLiant DL380 Gen10 chassis still in production?
A: No. HP stopped production of the Gen10 line in 2022. The chassis is now only available through the used or refurbished market.